Engine — Specifications Specifications Type 4-cylinder transversely mounted in-line engine, water-cooled, single overhead camshaft Engine: Code Displacement Dian. Piston stroke...
General description The models in question have a 4-cylinder in-line engine with an overhead camshaft, transversely mounted in the front of the car. Pic. 1.1. Engine 1.8 (18E)....
Engine — Routine Maintenance The procedures listed below must be performed at the frequency indicated at the beginning of this Manual. 1. Park the machine on a level surface and check the...
Work possible without removing the engine Without removing the engine from the car, you can perform the following work: A. Removing and installing the oil pressure regulator valve b. Replacing the...
Camshaft timing belt — replacement 1. Loosen the generator adjusting bracket and the bolts securing it, move the generator towards the engine and remove the drive belt from the pulleys. 2....
Camshaft — removal (the engine is on the car) 1. The procedure for replacing the camshaft is specified in sections 8 and 9. Although in principle it is not necessary to remove the cylinder head, it is...
Cylinder head — removal and installation The cylinder head can be removed along with the intake/exhaust manifolds and associated fuel system parts, or the whole thing can be disconnected from the head...
Pallet — removal and installation 1. Remove the drain plug and allow the engine oil to drain into a suitable container. Reinstall and tighten the plug. 2. On 1.3 engines, unscrew the bolts and...
Oil pump — removal and installation 1. Remove the camshaft timing belt ( see section 5 ) and rear shield. 2. Remove the central bolt of the crankshaft sprocket (if available). Using 2...
Flywheel — removal and installation 1. Remove the clutch ( see chapter 5 ). 2. Although the flywheel bolt holes are specifically offset so that the flywheel can only be installed the correct way,...
Engine/gearbox mounts — replacement 1. Engine/transmission mounts can be replaced if they are hardened or deformed. Support the engine with the gearbox with a jack (placing a wooden block between...
Engine — removal methods 1. The engine can be removed separately or together with the gearbox. 2. It is much easier to remove the engine separately. It is recommended to do this unless...
Engine — removal (together with manual gearbox) 1. Carry out the operations specified in paragraphs 1-8 section 18 . 2. Disconnect the gear shift lever from the gearbox ( see chapter 6 ). 3. Disconnect the...
Engine disassembly — general part 1. It is best to disassemble the engine on a special stand, but if this is not possible, you can use a workbench or even disassemble the engine directly on the...
Engine Accessories — Removal 1. Before disassembling the engine, the following auxiliary equipment must be removed from it: A. generator ( chapter 12 ) b. fuel pump ( chapter 3 ) V....
Engine — complete disassembly 1. Remove the engine and move it to a workbench. 2. Following the instructions in the previous sections, remove the following from the engine: A. camshaft...
Engine oil and oil filter — replacement 1. Engine oil and oil filter must be replaced at the intervals specified in section " Routine Maintenance " at the beginning of this manual (see photo). Photo...
Oil pump — bulkhead 1. Remove the pump from the engine, remove the Phillips screws and remove the rear cover of the pump. The screws are very tight and will require a Phillips...
Engine parts — inspection and repair or replacement Crankshaft 1. Inspect the crankshaft connecting rod and main journals for abrasion and scratches and measure them in several places using a micrometer. If the...
Engine — assembly (a common part) 1. In order to ensure maximum service life of a rebuilt engine, you should not only assemble it correctly, but also ensure that all parts are absolutely clean,...
Engine — assembly Crankshaft and main bearings 1. Check that the crankcase and crankshaft are immaculately clean and that the lubrication channels are cleaned. If possible, blow...
Engine — installation (together with manual gearbox) 1. With the front end of the machine raised and securely supported, place the engine and gearbox on the floor under the engine compartment (see photo). 2. Lift...
Engine — first start after major overhaul 1. Check that the battery is well charged, the fuel tank is full, and the engine is filled with oil and coolant. 2. If you disassembled the fuel system, you...
Engine — fault diagnosis Symptom/Cause (causes) The engine does not turn over with the starter/ There is no current flowing to the starter Battery is dead or faulty Poor contact at...