Car engine repair Opel Corsa C

Specifications for engine repair
General parameters Trade designation 1.0 1.0 1.2 1.4 1.4 1.6 Engine brand Z10XE Z10XEP Z12XE Z14XE Z14XEP Z16SE Year of issue 09/2000-08/2003 09/2003 09/2000...

General information about engines
1. Corsa C/Meriva, like any Opel model range, is traditionally distinguished by an extremely wide range of engines offered to consumers. The full list of...

List of works performed without removing the engine from the car
12. The following repairs can be performed without removing the engine from the vehicle: a) Compression check; b) Removing and installing the cylinder head...

Engine cover
1. Depending on the design features and the layout of the units in the engine compartment, some engines are equipped with a protective and decorative cover....

Checking the compression pressure in the cylinders
1. Measuring the compression pressure in the engine cylinders is one of the diagnostic tests. The results of this test allow you to determine the general...

Engine condition diagnostics using a vacuum gauge
1. Using a vacuum gauge at a relatively low cost allows you to obtain fairly comprehensive information about the internal condition of the engine. Based on the...

Removal and installation the multi-rib belt cover and engine crankcase protection
1. This Section contains some preparatory operations that are required to be performed when performing various maintenance and engine repairs. As a rule, they...

Removal the right engine mount
Note: Depending on the engine, the appearance, location and number of attachment points of the right support and its mounting bracket to the cylinder block may...

Removal and installation the crankshaft pulley
18. Before removing the pulley, the multi-rib belt must first be removed ( see Section 7 ). Note: It may be necessary to remove the right front wheel. 19....

Removal and installation camshaft sprockets/wheels
26. On engines with a timing belt drive, it is necessary to first remove the toothed belt ( see Section 8 ). On engines with a timing chain drive, the bolts...

Bringing the piston of the first cylinder to the top dead center (TDC) position
General information 1. Top dead center (TDC) is the highest point of the piston stroke in its cylinder. In 4-stroke engines, during the rotation of the...

Removal and installation the accessory drive belt
General information 1. The operations for removing and installing a multi-rib drive belt are in most cases similar for all engines, the differences are...

Removal and installation the timing belt/chain
General information The main purpose of the toothed belt/chain is to drive the gas distribution mechanism (GRM), while it ensures coordinated opening/closing...

Checking and adjusting the timing valves (engines Y17DT(L)/Z17DTH)
1. Most of the engines discussed in this Manual are equipped with valve tappets with hydraulic compensators. The valve clearance value on such engines is set...

Removal and installation of camshafts and valve lifters, checking of timing components
1. The procedure for removing/checking/installing camshafts is fundamentally similar for all engines. It is described in most detail for the...

Removal and installation the cylinder head
Caution: Cylinder head removal operations should only be performed on a cold engine (ambient temperature) engine! Note: The following is the procedure for...

Removal and installation the oil pan
Engines Z10XE(P)/Z12XE/Z14XEP 1. Remove the multi-rib belt cover and (with appropriate equipment) engine crankcase protection ( see Section 5 ). 2. Drain the...

Removal and installation the oil pump
1. On most engines considered in this Manual, the oil pump is driven directly by the crankshaft - the oil pump rotors are mounted on the shaft journal. If...

Measuring engine oil pressure
1. Warm up the engine during a short trip (up to 5 km) to operating temperature - approximately 80°C. 2. Stop the engine and apply the parking brake lever. 3....

Removal, checking condition and installing flywheel/drive disk
Removal 1. To remove the flywheel/drive shaft, you must first remove the transmission (see Chapter 6 or 7 ) and clutch ( see Chapter 6 ). 2. Using a suitable...

Replacing crankshaft seals
1. Typically, front oil seals (from the timing drive side) crankshaft are installed in the oil pump housing. A description of the procedure for replacing the...

Replacing camshaft seals
1. Description of the procedure for replacing camshaft seals (with appropriate equipment) given in Section 10 .

Checking the condition and replacing the powertrain suspension supports
Note: Depending on the engine brand and vehicle model, the power unit suspension can be carried out using three or four supports. Examination 1. The engine is...

Removal the engine
1. The format of the publication does not allow for a detailed description of the features of removing all engines considered in this Manual. Below is a...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information: