Car exterior Opel Astra G (petrol)

Technical data
Tightening torques (Nm)

General information
Astra models are available as a 4-door saloon, 3- and 5-door hatchback and 5-door estate. Zafira models are available as a minivan with 7 seats (MFV version of...

Body — maintenance and repair
1. The condition of your car's body is very important because it largely determines its resale value. It is much more difficult to repair a neglected or...

Body repair — minor damage
Repair of small scratches 1. If the scratch is superficial and does not affect the body metal, the repair is very simple. Lightly rub the scratched surface...

Body repair — significant damage
1. Significant damage to the body must be repaired at service stations that have equipment for body repair. 2. If there is extensive damage, the geometry of...

Hinges and Locks — Maintenance and Repair
Every 5,000 km or every three months, apply a few drops of light oil or lock lubricant to the hinges and latches on the doors, bonnet and trunk. The door lock...

Windshield and fixed glass — replacement
Replacing the windshield and fixed glass requires the use of a special fast-curing adhesive or sealant and some specialized equipment. It is recommended that...

Bumpers — removal and installation
Front bumper 1. Remove the three clips that secure the bumper to the front mudguard by pressing on the center pins. 2. Loosen the screws and remove the clips...

Radiator grille — removal and installation
1. The radiator grille is attached to the hood with 6 screws. Open the hood, unscrew the screws and remove the grille.

Box under the windshield (lining of the engine compartment niche) — removal and installation
1. Open the hood. 2. Remove the seal on the top edge of the engine compartment bulkhead. 3. Remove the deflector panel from the latches, disconnect the tubes...

Hood — removal, installation and adjustment
1. Open the hood. 2. Mark the position of the bolts on the hood hinges (see photo). 3. Unscrew the mounting bolts to the hinges and, with the help of an...

Hood hinges — removal and installation
1. Remove the hood. 2. Remove the engine compartment niche box. 3. Outline the contours of the hinges, unscrew the bolts and remove the hinges. 4. Installation...

Bonnet Lock Parts — Removal and Installation
Safety hook 1. The hook is attached to the hood with rivets that need to be drilled out (see photo). Lock retainer 2. Loosen the lock nut, unscrew the...

Hood Lock Drive Cable — Removal and Installation
1. Open the hood. 2. Unscrew the cable mounting bracket from the front bulkhead. 3. Disconnect the cable from the lever in the recess on the driver's side. If...

Doors — removal, installation and adjustment
Front door 1. Open the door and place a support underneath it. 2. Disconnect the connector on the front edge of the door by removing the bracket and turning...

Inner door handle — removal and installation
1. Remove the inner door panel, release the spring latch and push out the handle.

Outside Door Handle — Removing and Stopping
Front door handle 1. Remove the inner door panel, move the water-repellent screen, remove the rear window guide (see photo). 2. Remove the handle by following...

Door locks — removal and installation
Front door lock 1. Remove the inner door panel and pull back the water-repellent screen. 2. Raise the window and remove the rear window lift guide by drilling...

Drum switch lock — removal and installation
1. Remove the outer door handle. 2. Insert the key into the lock, then remove the retaining ring (see photo). 17.2 Details of the drum switch of the lock 1....

Door lock retainer
1. Draw the outline of the retainer, unscrew the bolts and remove the retainer.

Door glass — removal and installation
Front doors 1. Remove the inner door panel and water-repellent screen. 2. Disable the side airbag by disconnecting the battery from ground and waiting 1...

Window lifter — removal and installation
Front door window lifter 1. Remove the front door glass. The further procedure for removing the window regulator is illustrated in the photo. 2. Installation...

Trunk lid — removal and installation
1. On models with a power lid lock, disconnect the battery from ground and disconnect the wires from the actuator. Tie the wires to a wire and pull them out of...

Trunk lid hinge — removal and installation
1. Remove the cover. 2. Remove the rear trim panel (see below). 3. Mark the position of the balance spring on the bracket and unhook the spring. 4. Loosen the...

Trunk Lid Parts — Removal and Installation
Lock 1. Remove the drum lock switch (see below). 2. Unscrew 2 bolts and remove the lock. 3. When assembling, adjust the position of the lock. Drum switch lock...

Rear Compartment Cover — Removal and Installation
1. Remove both inner panels of the lid (see photo), unscrewing the screws (the screws are covered with plugs, which you can pry up and remove). 2. Remove the...

Rear Compartment Lid Hinges — Removal and Installation
1. Remove the rear compartment cover. 2. Remove the seal from the top edge of the rear compartment opening. 3. Remove the trim panels from the rear pillar on...

Rear Compartment Lid Parts — Removal and Installation
Lid stand 1. Open the lid and have an assistant hold it. 2. Remove the spring clips from the lid posts, disconnect the posts from the ball joints (see photo)....

Centralized locking system parts — removal and installation
Control unit If the block is to be changed, it should be adapted in a car service center. 1. The control unit for the central locking system is mounted in the...

Electric window lifter parts — removal and installation
Switches 1. The switches are mounted on the doors on the driver and passenger sides. 2. Pry up and remove the switch, disconnecting the wire. Electric window...

Outside rear view mirror — removal and installation
1. Remove the inner door panel. 2. Disconnect the wires leading to the mirror, remove the seal from the inner door panel (see photo). 3. To access the mounting...

Optical element of the outside mirror — removal and installation
1. Carefully press on the upper corner of the mirror element located closer to the door. Use a screwdriver to pry up and release the lower one from the frame...

Exterior Mirror Parts — Removal and Installation
Switches 1. The outside mirror switches are mounted on the driver and passenger side doors. 2. Pry up and remove the switch, disconnecting the wire. Electric...

Windscreen, Rear Window and Corners — General Information
1. These glasses are glued in place with special glue. Dismantling and replacement of the glasses is performed in a car service.

Sunroof glass panel — removal and installation
1. Move the light filter back, open the sunroof glass halfway. 2. Unscrew the 4 bolts at the front of the glass panel and remove the casing. 3. Loosen the...

Hatch components and parts — removal and installation
Attention! It is not recommended to disassemble the hatch unless absolutely necessary. Repair of the hatch drive mechanism is performed in a car service...

Wing Guards — Removal and Installation
1. The wing guards are secured with screws, plastic bolts and latches. Some latches are removed by pressing on the central rod. 2. Some vehicles are equipped...

Fuel filler cap — removal and installation
1. Open the cover, unscrew 2 screws and remove.

Exterior body trim parts — removal and installation
Door edging 1. Remove the inner door panel, unscrew the screw securing the trim through the opening in the frame (see photo). 2. On the front door, pry up the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Мешки для мусора оптом

Share information: