General information The car uses a load-bearing body structure designed to reflect the identity and originality of the brand, while at the same time improving the capacity,...
Front bumper device 1. Energy absorbing element of the front bumper. 2. The lower beam of the front bumper. 3. Facing the front bumper. 4. Molding grille. 5. External inserts...
Replacement of facing of a forward bumper Basic version 1. Disconnect the front parts of the front fender liner. 2. Remove six top fasteners (1) front bumper. 3. Loosen, but do not completely remove...
Front bumper battery replacement 1. Remove front bumper trim. 2. Unhook four latches (arrows) and remove the power accumulator of the front bumper (1). 3. Installation is made in an order, the...
Front bumper center support bracket replacement 1. Remove front bumper trim. 2. Remove four screws (1) fixing the center support bracket of the front bumper cladding. Note. Tightening torque: 9 Nm. 3. Remove...
Replacing the front bumper beam 1. Remove front bumper trim. 2. Remove four screws (1) fastening of a beam of a forward bumper. Note. Tightening torque: 22 Nm. 3. Remove the front bumper beam...
Replacing the lower beam of the front bumper 1. Remove front bumper trim. 2. Unscrew the three mounting bolts (1) and remove the lower beam of the front bumper (2). 3. Installation is made in an order,...
Rear bumper device 1. Facing the rear bumper. 2. Hole cover for the rear towing eye. 3. Insert rear bumper lining.
Replacement of facing of a back bumper Sedan/hatchback 1. Remove the rear signal lights. 2. Remove six bolts (1) rear bumper trim. Note. It is necessary to pry off the rear fender liner to gain...
Rear bumper battery replacement Sedan/hatchback 1. Remove the rear bumper trim. 2. Remove the rear bumper energy accumulator. 3. Installation is made in an order, the return to removal....
Replacing the rear bumper beam Sedan/hatchback 1. Remove the rear bumper trim. 2. Remove the rear bumper energy accumulator. 3. Remove six nuts (1) rear bumper beams. Note. Tightening...
Front fender replacement 1. Remove front bumper trim. 2. Remove the headlamp. 3. Remove the front and rear of the front fender liner. 4. Remove the front side turn signal. 5. To remove...
Door replacement 1. Disconnect the door electrical connector. 2. Support the door with a jack, then unscrew the bolt (1) front door stop. Note. Tightening torque: 22 Nm. Front...
Front door adjustment 1. Loosen the four bolts securing the front door hinges to the body. 2. Adjust the position of the front door (1) to obtain uniform gaps. A. Clearance between...
Rear door adjustment 1. Loosen the four bolts securing the rear door hinges to the body. 2. Adjust the position of the tailgate (1) to obtain uniform gaps. A. Gap between rear door...
Hood replacement 1. Disconnect the hood support legs. 2. Unscrew the four fastening nuts (1) and remove the hood (2). Note. Tightening torque: 20 Nm. If the hood is to be...
Hood adjustment 1. Loosen the four hood hinge bolts. 2. Adjust the position of the hood (1) to obtain uniform gaps. A. Gap between hood and front bumper lining: 3.5mm±1mm. B....
Tailgate Replacement Attention. If the support legs are removed, alternate hood support must be provided to prevent vehicle damage or personal injury. 1. Remove the inner lining of...
Tailgate Adjustment 1. Loosen the four bolts securing the tailgate hinges to the body. 2. Adjust the position of the tailgate (1) to obtain uniform gaps. Wagon: A. Gap between...
Trunk lid Trunk lid replacement 1. Remove the inner lining of the trunk lid. 2. Remove four screws (1) trunk lid fasteners. Note. Tightening torque: 22 Nm. 3. Disconnect...
Trunk lid adjustment 1. Loosen the four bolts of the trunk lid hinges. 2. Adjust the position of the trunk lid (1) to obtain uniform gaps. A. Gap between trunk lid and body panel:...
Replacing the fuel filler flap Fully open the fuel tank door. Slightly push the sunroof outward to disengage the sunroof latch from the hinge.
Body dimensions The specified body dimensions are for reference only. All measurements are given in millimeters. The given dimensions are used to diagnose and evaluate the...