Devices for safe transportation of children in a car (Opel Frontera A)

Contents: Baby Carrier Seat ⬇ Seat for transporting young and…⬇

The set includes: a child seat for transporting infants, a seat for transporting younger children and an additional cushion for transporting pre-teens (are also issued individually).

The baby car seat covers are easily removed for washing.

Child seats are secured to the main vehicle seat using standard three-point seat belts.

If the seat is damaged during an accident, it must be replaced. See also the instructions included in the kit.

Baby Carrier Seat

These seats are designed to carry children up to 10 months of age and weighing up to 10 kg.

Warning! It is prohibited to install a rear-facing child seat in the front seat of vehicles equipped with an airbag!

Place the child in the seat.

1. Connect the buckles of the two shoulder belts of the child seat together and tuck them into the buckle located between the child's legs.

The length and height of the child seat belt can be adjusted to the anthropological characteristics of a particular child.

2. To adjust the length of the belts, pull the free end of the lower section of the belt behind the seat, or, conversely, release it by pressing the metal clamp of the lock.

Note: The belt should fit snugly against the child's body without being too tight.

3. To adjust the height of the position, pull both shoulder straps out of their installation slots and thread them into the other slots located at the desired height.

4. Press down on the child seat's handle to release the lock, then pull the handle up to lock it in the raised position.

5. Place the child seat in the main passenger seat of the vehicle, facing rearward.

Please note! The last instruction does not apply when installing a child seat on the front seat of a vehicle equipped with an airbag (see above)!

6. Move the upper anchor of the main seat belt to the lowest position.

7. Pull the main seat belt out of the retractor and thread the lap portion of the belt under the two guides on the child seat.

8. Fasten the seat belt buckle.

9. Open the clip on the back of the child seat.

10. Place the diagonal portion of the seat belt over the back of the child seat and into the open clip.

11. Close the clamp.

12. Press down on the child seat's carrying handle to release the lock.

(Material published on the website: «www.opelbook.ru»)

13. Lower the handle down to the transport position.

Seat for transporting young and pre-teen children

Opel produces both an adjustable seat that can be adjusted to accommodate different weight loads (see fig. 3.13), and also separate cushions for seating pre-teen and early teenage children.

Adjustable seat assembly (pillow with backrest) designed for transporting young children weighing from 10 to 25 kg.

After detaching the backrest, the seat cushion can be used to transport pre-teen children weighing between 18 and 36 kg.

1. When used to transport children of the first weight category (10-25 kg), install the seat assembly with the backrest on the front or side rear seat of the vehicle, facing the direction of travel.

2. Press the child seat back firmly against the back of the main seat.

Caution! When installing a child seat on the front seat of a vehicle equipped with a front passenger airbag, move the main seat to the rearmost position!

3. Place your child in the child seat.

4. Lower the upper seat belt anchor of the main seat to the lowest position.

5. Insert the seat belt buckle into the buckle.

6. As shown in the illustration, thread the lap portion of the belt through the guide hooks on the child seat.

7. Open the valve on the outer upper adjuster of the child seat and thread the diagonal part of the seat belt through the adjuster, then close the valve again.

8. Loosen the plastic-headed bolt/remove the fastening pin and adjust the belt position as required, either by lifting it up in the clamp or by lowering it down.

9. Retighten the bolt/reinsert the pin.

Note: The seat belt should go over the child's shoulder without touching the neck area or restricting the freedom of movement of the arms.

10. To transport children of the second weight category (18-36 kg), detach the backrest from the seat by loosening the outer screws securing it to the cushion using a screwdriver.

11. Working from the inside, remove the stud bolts from the cushion.

12. Separate the backrest from the seat cushion.

13. Place all unnecessary components in a safe place.

14. Place the cushion on the main seat of the vehicle, facing the direction of travel.

Caution! When installing a child seat on the front seat of a vehicle equipped with a front passenger airbag, move the main seat to the rearmost position!

15. Place your child in the child seat.

16. Lower the upper seat belt anchor of the main seat to the lowest position.

17. Insert the seat belt buckle into the buckle.