General information
| Working volume, cm³ | 3165 |
| Cylinder diameter, mm | 93,4 |
| Piston stroke, mm | 77 |
| Power, kW/min⁻¹ | 151/5400 |
| Power, hp/min⁻¹ | 205/5400 |
| Torque, Nm/min⁻¹ | 290/3000 |
| Compression | 9,4:1 |
| Octane number of fuel | RON95 |
| Fuel injection system | MPFi |
Cylinder head
| Cylinder head height, mm: - nominal | 133,2 |
| - minimum | 133,0 |
| Deviation of flatness of the mating surface of the cylinder head, mm: - nominal | 0,05 |
| - maximum permissible | 0,20 |
Valves
| Valve stem diameter, mm: - intake | 5,959-5,977 |
| - graduation | 5,952-5,970 |
| Minimum allowable valve stem diameter, mm | 5,90 |
| Width of the working part of the valve plate, mm | 1,13 |
| Minimum allowable width of the working part of the valve plate, mm | 0,63 |
| Valve stem protrusion relative to spring seat base, mm: - nominal | 42,50 |
| - maximum | 42,85 |
| Clearance between valve guide and valve stem: - intake | 0,023-0,056 |
| - graduation | 0,030-0,063 |
| Maximum permissible clearance between the guide bushing and the valve stem, mm: - intake | 0,20 |
| - graduation | 0,20 |
| Valve guide bushing protrusion, mm | 17,5 |
| Valve springs: - permissible non-perpendicularity, mm | 2,2 |
| - length, mm: - nominal | 50,1 |
| - minimum acceptable | 48,1 |
Camshafts
| Camshaft cam height, mm: - nominal | 34,24 |
| - minimum acceptable | 37,18 |
| Diameter of camshaft bearing journals, mm: - nominal | 44,94-44,96 |
| - minimum acceptable | 44,79 |
| Minimum permissible ovality and taper of camshaft bearing journals, mm | 0,05 |
| Axial clearance of the camshaft, mm: - nominal | 0,07-0,20 |
| - maximum permissible | 0,25 |
Connecting rods
| Diameter of the hole in the lower head of the connecting rod, mm. - class A | 56,994-57,00 |
| - class B | 56,988-56,994 |
| - class C | 56,982-56,988 |
| Thickness of crankshaft connecting rod bearing liners, mm: - class A | 1,512-1,516 |
| - class B | 1,508-1,512 |
| - class C | 1,504-1,508 |
Crankshaft
| Clearance in connecting rod bearings of crankshaft, mm: - nominal | 0,025-0,058 |
| - maximum permissible | 0,12 |
| Clearance in crankshaft main bearings, mm: - nominal | 0,26-0,049 |
| - maximum permissible | 0,12 |
| Crankshaft axial clearance, mm: - nominal | 0,06-0,24 |
| - maximum permissible | 0,30 |
| Diameter of crankshaft main journals, mm | 63,918-63,933 |
| Diameter of crankshaft connecting rod journals, mm | 53,922-53,937 |
Pistons
| Piston outer diameter, mm: - mark A | 93,360-93,370 |
| - mark B | 93,371-93,380 |
| - mark C | 93,381-93,390 |
| Cylinder diameter, mm: - class A | 93,400-93,410 |
| - class B | 93,411-93,420 |
| - class C | 93,421-93,430 |
Piston rings
| Lateral clearance of compression rings, mm: - nominal | 0,016-0,038 |
| - maximum permissible | 0,15 |
| Clearance in piston ring locks, mm: - nominal: - compression ring No. 1 | 0,35-0,47 |
| - compression ring No. 2 | 0,45-0,60 |
| - oil scraper ring | 0,15-0,45 |
| - maximum permissible | 1,5 |
Cylinder block
| Diameter of the bed for crankshaft main bearing shells, mm: - size mark 1 | 68,994-69,000 |
| - size mark 2 | 68,987-68,993 |
| - size mark 3 | 68,980-68,986 |
Attachment drive belt
| Used belt deflection when checking tension, mm | 8-12 |
| Tension, N: - generator drive belt: - new belt | 1798±98 |
| - used belt | 1081±98 |
| - air conditioning compressor drive belt: - new belt | 1179±197 |
| - used belt | 980±197 |
| - power steering pump drive belt | 885±197 |
Lubrication system
| Engine oil capacity, l | 5,2 |
Oil pump
| Maximum permissible clearance between the outer rotor and the oil pump housing, mm | 0,20 |
| Maximum permissible gap between the teeth of the oil pump rotors, mm | 0,35 |
| Maximum permissible lateral clearance of oil pump rotors, mm | 0,15 |
Cooling system
| Coolant volume, l: - cars with manual transmission | 8,8 |
| - cars with automatic transmission | 8,4 |
| Radiator fan drive | Viscous coupling |
| Number of radiator fan blades | 8 |
| Water pump capacity, l/min | not less than 300 |
Thermostat
| Temperature of the beginning of opening of the thermostat valve,°C | 74,5-78,5 |
| Temperature of full opening of thermostat valve,°C | 90 |
Coolant
| Water/antifreeze content at freezing temperature, l: - cars with manual transmission: - below -10°C | 7,04/1,76 |
| - below -20°C | 5,80/3,0 |
| - below -30°C | 4,9/3,9 |
| - below -40°C | 4,22/4,58 |
| - cars with automatic transmission: - below -10°C | 6,72/1,68 |
| - below -20°C | 5,54/2,87 |
| - below -30°C | 4,7/3,7 |
| - below -40°C | 4,03/4,37 |
Tightening torques for threaded connections, Nm
| Oil pan mounting bolts | 25 |
| Bolts and nuts for fastening the rear beam to the front part of the frame | 50 |
| Rear Oxygen Sensor | 42 |
| Front right oxygen concentration sensor | 42 |
| Front left oxygen concentration sensor | 42 |
| Exhaust manifold to cylinder head mounting nuts | 52 |
| Front exhaust pipe to exhaust manifold mounting nuts | 43 |
| Spark plugs | 18 |
| Camshaft pulley mounting bolt | 98 |
| Bolts and nuts for fastening the expansion air chamber | 25 |
| Camshaft bearing cap mounting bolts | 10 |
| Cylinder head cover mounting bolts | 8 |
| Cylinder head mounting bolts: - 1st pass | tighten the bolts to 29 Nm |
| - 2nd pass | tighten the bolts to 64 Nm |
| Bolts securing the exhaust gas recirculation pipe to the cylinder head | 28 |
| Power steering pump bracket mounting bolts | 22 |
| Power steering pump mounting bolts | 46 |
| Cooling system manifold to cylinder head mounting bolts | 22 |
| Bolts and nuts for fastening the fan pulley assembly to the cylinder block | 24 |
| Nuts securing the radiator fan to the viscous coupling pulley | 10 |
| Cylinder head cover mounting bolts | 9 |
| Ignition coil mounting bolts | 4 |
| Flywheel mounting bolts | 54 |
| Bolts securing the crankcase to the cylinder block | 10 |
| Connecting rod cap mounting bolts | 54 |
| Oil gallery mounting bolts: - 1st pass | tighten the bolts to 29 Nm |
| - 2nd pass | tighten the bolts to an angle of 55-65° |
| Crankshaft pulley mounting bolt | 167 |
| Cylinder Block Rear Cover Fastening Bolts 18 | |
| Oil pickup tube mounting bolts with mesh filter | 25 |
| Side bolts for fastening the crankshaft main bearing caps | 39 |
| Oil pump mounting bolts | 25 |
| Safety valve retainer mounting screws | 8 |
| Oil pump cover mounting screws | 10 |
| Thermostat pipe mounting bolts | 25 |
| Water pump mounting bolts | 25 |
| Camshaft Pulley Mounting Bolts | 98 |
| Idler roller mounting bolt | 52 |
| Crankshaft position sensor mounting bolt | 10 |
| Bolts securing the propeller shaft to the front axle | 63 |
| Fuel rail mounting bolts | 25 |
| Coolant temperature sensor | 30 |
| Engine Air Intake Temperature Sensor | 4 |
| Knock sensor | 20 |
| Throttle assembly | 25 |
| Camshaft Position Sensor | 9 |
| Accelerator pedal mounting bolts | 10 |
| Bolts for fastening gear belt covers of the gas distribution mechanism drive | 19 |
| Air conditioning compressor mounting bolts | 19 |
| Bolts for fastening the hydraulic timing belt tensioner to the cylinder block | 25 |
| Generator mounting bolts: - M10 bolts | 41 |
| - M8 bolts | 21 |
| Generator pulley mounting nut | 111 |
| Hollow bolts for fastening fuel lines | 25 |
| Starter mounting bolts | 38 |
Visitor comments