Cleaners
The injection and air damper cleaner is a powerful solvent for resins, carbon deposits and carbon deposits. Most cleaners leave behind a dry-type lubricating film that does not harden or become resinous over time. It is because of the formation of such a film that these cleaners are not recommended for use in cleaning electrical components.
Brake system cleaner is used to remove traces of grease and brake fluid from the surfaces of brake system components, where absolute cleanliness is a primary condition for efficient operation. The cleaner leaves no traces and in many cases eliminates the squeal of brake mechanisms caused by contamination of their components.
The electrical component cleaner helps remove oxide films, traces of corrosion and carbon deposits from contact surfaces without disrupting electrical conductivity. It can also be used to clean spark plugs, jets, voltage regulators and other components where complete removal of oil and grease is desired.
Desiccants are used to remove water and moisture from the surfaces of electrical components such as generators, voltage regulators, fuse boxes, electrical connectors, etc. Desiccants are typically non-conductive, non-corrosive, and non-flammable.
Degreasers are super-strong solvents and are used to remove traces of grease from the outer surfaces of the engine and chassis components. They are available as aerosols or applied with a brush or brush and, depending on the type, are washed off with either water or solvent.
Lubricating fluids
Engine oils are specially designed compounds for lubricating internal engine components. They usually contain a wide range of different additives that prevent foaming and corrosion. Engine oils are available in different viscosity grades, each viscosity grade is assigned its own code - from 0 to 60 (sAE Standards System). The need to use a particular type of oil is determined by climatic conditions and the requirements of a particular engine (see Chapter 1). Liquid (light) oils are usually used in cold climates and with low engine loads. Heavy (viscous) oils are used in hot conditions and with increased engine loads. All-season oils have the characteristics of both light and heavy oils and are usually designated from 5W-20 to 20W-50.
Qualities of motor oils
All-season oils are relatively inexpensive oils with the following qualities:
- Year-round use in temperate climate zones;
- Excellent cleaning properties;
- Good lubricating ability at all temperatures and engine loads;
- High stability of initial properties over a long period of time.
All-season oils with improved antifriction properties also have additional advantages:
- Possibility of year-round use at almost all possible outdoor temperatures;
- Low engine power losses due to friction;
- Facilitates cold engine starting - even at very low temperatures.
Note: Due to their specific viscosity-temperature properties, seasonal oils usually cannot be used all year round. Therefore, these oils should only be used in extreme climate zones.
Additives for motor oils
No friction reducing additives should be added to engine oils.
Mixing oils
This and similar questions interest many car enthusiasts. Unfortunately, there is no clear answer to them. Modern oils include various additives that improve their properties. When using oils of different grades together, these additives can enter into chemical reactions with each other, form an abrasive sediment and/or change the properties of the oils, which can lead to unforeseen consequences and engine failure. Each company produces commercial oils, adding additives to the oil base, the chemical composition of which is kept secret. Therefore, many high-quality oils of the same purpose, but produced using technologies from different companies, can create low-quality mixtures when mixed. Oils from different companies are interchangeable, the possibility of using such oils is often indicated by engine developers. But this does not mean that they can be mixed.
(Information taken from the website: OPELBOOK)
Attention: Never add oil of another modification unless you have absolutely precise information about the compatibility of these oils!
The same applies to mixing mineral or synthetic oils (even one company). Oils of the same brand can be mixed only if the oil manufacturer recommends it and is responsible for it. Unfortunately, there are often cases when mixing oils deteriorates their quality, and long-term use of these mixtures is unacceptable, since this may result in the engine "knocking".
Today, some car enthusiasts still believe that a diesel engine will "eat" everything. But the time of low-speed diesel engines of the early and mid-20th century, which did not impose relatively high demands on oil quality, has long passed. Attempts to fill a modern diesel engine with oil whose quality does not meet the requirements of a specific engine brand will inevitably lead to its failure.
It is necessary to make it a rule: to use high-quality oil of the same brand corresponding to the engine (by classification), to top up the system, have a small amount of the appropriate oil in a tight, hermetically sealed container in the car. The engine will thank you for this with reliable operation. Do not buy oil from someone, as the packaging is easy to counterfeit!
The transmission oil is designed for use in differentials, gearboxes, and other components where resistance to high temperatures is required.
Chassis Component and Wheel Bearing Grease is a thick grease used in high load and friction applications such as wheel bearings, suspension ball joints, tie rod ends and universal joints.
High-temperature wheel bearing grease is able to withstand the effects of high temperatures that occur in wheel bearings of vehicles equipped with disc brakes. Typically contains molybdenum disulfide, which is a dry-type lubricant.
White grease (tsiatim) is a thick grease applied to metal surfaces in contact with each other in places where there are problems with increased moisture. It remains soft at both low and high temperatures, and is not washed out or diluted by water.
Assembly grease is a special grease for use under high pressure conditions, usually contains molybdenum and is used to lubricate components subject to increased loads (such as main and connecting rod bearings and cam lobes) before the first engine start after completion of a major overhaul.
Silicone greases are used to protect rubber, plastic, vinyl and nylon components. Graphite greases are used where oil cannot be used due to contamination problems (for example, in castles). Dry graphite perfectly lubricates metal parts, preventing the impact of moisture, acids and other aggressive contaminants on them. The lubricant is electrically conductive and does not disrupt contact in such units as, for example, the ignition switch.
Molybdenum-containing penetrating compounds are used to facilitate the release of "stuck" fasteners, as well as to lubricate fasteners to prevent future corrosion. Thermally conductive grease is non-conductive and is used to install electronic ignition modules that require intensive heat removal.
Sealants
RTV sealant is the most widely used gasket sealant. It is silicon-based, air-curing, provides sealing, adhesion, is waterproof, fills surface defects, remains flexible, does not shrink or shrink, is relatively easy to remove, and is used in addition to almost all gaskets on units where temperatures do not exceed average values.
Unlike RTV sealant, anaerobic sealant can be used not only in addition to gaskets, but also to form them. It remains elastic, is resistant to solvents and fills surface irregularities well. The main difference from RTV sealant is in the curing conditions. While RTV sealant begins to harden after exposure to air, anaerobic sealant only hardens in the absence of air. This means that such sealant hardens only after assembling the components and pressing them tightly together.
Pipe and thread sealant is used to seal nipple connections of hydraulic, pneumatic and vacuum lines. It is usually made on the basis of a Teflon compound and supplied in the form of aerosols applied like paint, liquids or in the form of tape (FUM).
Chemicals
Anti-seize compound is used to prevent "sticking", corrosion, jamming and cold welding of fasteners. High-temperature anti-seize sealants are usually made on the basis of copper-containing or graphite lubricants and are used in fasteners of the exhaust system and exhaust manifold.
Anaerobic fixing compounds are used to prevent spontaneous loosening of fasteners under the influence of vibrations and harden only after installation in the absence of contact with air. Medium-strength fixing compounds are used to fix small fasteners (nuts, bolts, screws), which are subject to regular release in the future. High-power compounds are usually used to lock large fasteners that are not released on a regular basis.
Oil additives serve to change the chemical properties of the oil without changing its viscosity in order to reduce internal friction in the engine. It should be noted that most manufacturers of motor oils warn against the use of any additives to them.
Fuel additives perform several functions at once, depending on their chemical composition. They usually contain solvents that help remove slag and carbon deposits from the internal surfaces and components of the fuel injection system and intake tract. In addition, the use of such additives helps remove carbon deposits that form on the walls of combustion chambers. Some additives contain substances that serve to lubricate the components of the upper part of the cylinder head (valve mechanism, piston rings), while others help remove condensation from the walls of the fuel tank.
Others
Brake fluid is a specially formulated compound that can withstand the effects of high temperatures and pressures that occur in the brake system. Avoid contact of brake fluid with painted surfaces of the car and exposed areas of the body. Brake fluid is poisonous. Keep brake fluid in a hermetically sealed container to prevent moisture from getting into it (the liquid is very hygroscopic) and dirt.
During vehicle operation, brake fluid absorbs a certain amount of water from the surrounding air. Too much water in the brake fluid can eventually cause corrosion of the working brake system components. In addition, the boiling point of the brake fluid is significantly reduced.
Therefore, you should change the brake fluid at least once every two years!
Caution: If the brake fluid is very old, it is possible that, under high load on the service brake system, steam bubbles may form in the system. This has a negative effect on the efficiency of the service brake system and, therefore, on traffic safety!
Note: Use only recommended brake fluid (DOT 4).
Adhesive for fastening sealing strips of body openings, as its name suggests, is used to fasten sealing strips of door openings, windows and trunk lids. It can be used to fix interior trim elements.
Anti-corrosion coating for the underbody of a car is a tar-like composition made on an oil base and serves for a protective coating of metal surfaces, preventing their corrosion. In addition, it performs the function of soundproofing the interior.
Waxes and polishes are used to protect painted surfaces from environmental influences. Different types of paint may require different types of waxes and polishes. Some polishes contain abrasives or chemical additives that remove the outer layer of oxides (tarnishings) from the painted surfaces of old cars. Recently, various types of wax-free polishes have become widely available on the market, which contain many chemical additives such as polymers or silicon-based substances. Such polishes are usually easier to apply and last longer than regular (wax) polishes.
Visitor comments