The front suspension is fully independent and uses MacPherson struts with coil springs and telescopic dampers. The rear suspension is also fully independent. Front and rear suspension have anti-roll bars.
Suspension and steering specifications Front suspension Type Independent suspension with MacPherson struts, screw springs, anti-roll bar and telescopic shock absorbers. with adjustable camber Rear...
Front suspension strut Removing 1. Remove the corresponding wheel. 2. Remove the brake caliper. 3. Remove the mounting clip. 4. Remove the hydraulic hose from the bracket on the...
Front wheel camber Adjustment 1. Remove the front wheels and brake calipers. 2. Replace the stub axle mounting bolts and nuts. 3. Set the front camber to maximum by tilting the...
Lower arm front suspension Removing 1. Remove the corresponding front wheel. 2. Loosen the pinch bolt and lower the suspension arm down, disengaging the ball joint from the stub axle. 3....
Lower control arm ball joint, front suspension Replacement 1. Remove the suspension arm. 2. Drill out the fixing rivets (indicated by arrows) ball joint. 3. Lubricate the holes with an anti-corrosion...
Stabilizer bar of the front suspension Removing 1. Remove the front wheels. 2. Turn off fixing nuts and disconnect connecting links from the anti-roll bar. 3. Remove the front suspension cross...
Connecting links of the stabilizer bar Removing 1. Remove the corresponding front wheel. 2. Loosen the top nut. 3. Disconnect the link from the suspension strut. 4. Disconnect the link from the...
Stub axle — removal and installation Removing 1. Remove the front wheel hub and brake shield. 2. Loosen the tie rod ball joint retaining nut and disconnect the tie rod using a ball joint splitter....
Front wheel hub and bearings Removing 1. Loosen the hub mounting nut. 2. Remove the brake caliper and brake disc. 3. Loosen the fixing nut. 4. Remove the fixing nut. 5. Remove the hub from...
Front suspension crossbar Removing 1. Remove the protective panel from the bottom of the engine. 2. Disconnect the ball joints of the suspension arms from the pivot pins. 3. Disconnect...
Rear shock absorber Removing 1. Raise the appropriate rear suspension arm to reduce shock load. 2. Remove the carpet or trim panel and loosen the top shock mount nuts. 3. On...
Rear suspension arm — removal and installation Removing 1. Remove the axle shaft from the rear wheel hub. 2. Remove the brake caliper and brake disc. 3. Remove the handbrake cable from the lever. 4....
Rear suspension springs — removal and installation Removing 1. Lower the rear of the exhaust system about 300mm. 2. Disconnect the rear suspension height sensor connector. Mark the position of the sensor arm...
Stabilizer bar of the rear suspension Removing 1. Disconnect the rear suspension height sensor connector. Mark the position of the sensor arm and disconnect it from the anti-roll bar connecting...
Transverse rods of the rear suspension Removing 1. Unscrew the nut (arrow), which secures the rod to the suspension arm. 2. Disconnect the rod from the lever. 3. unscrew the bolt (indicated by an...
Rear suspension height adjustment system System check 1. Park the vehicle on a level surface and start the engine. 2. Measure the height of the rear suspension. 3. Put a heavy load in the trunk and...
Rear suspension — removal and installation Removing 1. Remove intermediate and back sections of an exhaust system. 2. Remove the handbrake cable balancer. 3. Remove the brake calipers. 4. Remove the ABS...
Rear suspension cross member Removing 1. Remove the rear suspension. 2. Remove the anti-roll bar from the cross member. 3. Unscrew the fixing bolts and remove the main gear from the cross...
Rear suspension crossbar mounts Removing 1. Lower the rear of the exhaust system about 30 cm. 2. Remove the brake hoses from the brackets on the suspension arms. 3. Establish a support under...
Rear wheel hub and bearings Removing 1. Unscrew the axle shaft fixing nut and remove the axle shaft from the hub. 2. Remove the brake caliper. 3. Remove the lower shock absorber mounting...