OHV engine inspection and repair Opel Kadett E
Adjusting clearances in the valve drive mechanism
Remove the cylinder head cover. Turn the crankshaft so that the piston of the 1st cylinder, counting from the side of the valve timing drive, occupies the TDC...
Remove the cylinder head cover. Turn the crankshaft so that the piston of the 1st cylinder, counting from the side of the valve timing drive, occupies the TDC...
Removal and installation the ignition system distributor
Removal Turn the engine crankshaft to the TDC position of the end of the compression stroke of the piston of the 1st cylinder. In this case, the mark on the...
Removal Turn the engine crankshaft to the TDC position of the end of the compression stroke of the piston of the 1st cylinder. In this case, the mark on the...
Adjusting the gap between the contacts of the ignition system interrupter
Adjusting the gap using a set of feeler gauges Remove the distributor cap. Engage 4th gear and, while moving the vehicle, turn the crankshaft so that the...
Adjusting the gap using a set of feeler gauges Remove the distributor cap. Engage 4th gear and, while moving the vehicle, turn the crankshaft so that the...
Setting the ignition timing
Setting the ignition timing using a test lamp with the engine off. Loosen the distributor lock plate mounting bolt. Connect the test lamp with one wire to the...
Setting the ignition timing using a test lamp with the engine off. Loosen the distributor lock plate mounting bolt. Connect the test lamp with one wire to the...
Fuel pump
Removing and installing the fuel pump on the cylinder block is not difficult. Check the fuel supply pressure at a crankshaft speed of 2000 rpm. It should be...
Removing and installing the fuel pump on the cylinder block is not difficult. Check the fuel supply pressure at a crankshaft speed of 2000 rpm. It should be...
Operating principle of the Weber 32 TL carburetor
Starting device When the control handle is pulled, the choke valve closes and the throttle valve opens slightly as a result of the movement of the control...
Starting device When the control handle is pulled, the choke valve closes and the throttle valve opens slightly as a result of the movement of the control...
Main metering system of the Weber 32 TL carburetor
Fuel is fed through the filter and the needle valve into the float chamber. From the float chamber, fuel enters through the main fuel jet into the emulsion...
Fuel is fed through the filter and the needle valve into the float chamber. From the float chamber, fuel enters through the main fuel jet into the emulsion...
Adjusting the starting clearance of the carburetor throttle valve
Adjustment on a removed carburetor Move the air damper control lever all the way to the stop and make sure that the air damper is completely closed. Measure...
Adjustment on a removed carburetor Move the air damper control lever all the way to the stop and make sure that the air damper is completely closed. Measure...
Oil filter
The oil filter is full-flow. The filter is replaced every 15,000 km. When replacing, the filter housing is unscrewed and screwed on manually. To make it easier...
The oil filter is full-flow. The filter is replaced every 15,000 km. When replacing, the filter housing is unscrewed and screwed on manually. To make it easier...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
See similar ones from other Opel car manuals:
▶ Power unit: Repair of gasoline engines Opel Omega B (1993-1999)
▶ Body: Repair and care Opel Frontera A (1991-1998, petrol)
▶ Power unit: Repair of gasoline engines Opel Omega B (1993-1999)
▶ Body: Repair and care Opel Frontera A (1991-1998, petrol)
Share information:
- General information
- Vehicle description
- Operation and maintenance
- OHV power unit
- Engine design
- Check and repair
- Engine work
- OHC power unit
- Engine design
- Engine repair
- Ignition system
- Cooling and lubrication
- Supply system
- Fuel injection «LE-Jetronic»
- Fuel injection «LE3-Jetronic»
- Motronic ML4.1 system
- Motronic M1.5 system
- Motronic M2.5 system
- Transmission
- Clutch
- Gearbox F10 and F13
- Gearbox F16 and F20
- Automatic gearbox
- Drive shafts
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- Car care
- Maintenance
- Power unit
- Gasoline engines
- Lubrication system
- Cooling system
- Power system (gasoline)
- Carburetor Solex 35 PDSI
- Carburetor Varajet II
- Carburetor 1B1
- Fuel injection (gasoline)
- Diesel engines
- Fuel system (diesel)
- Transmission
- Clutch
- Manual gearbox
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body
- Body elements
- Doors and windows
- Electrical equipment
- Equipment and devices
- Lighting system
- Power devices
- Ignition system
- Electrical circuits

